Artepoxy Liquid Marble - Metallic Epoxy Resin

Product Notes

• Application onto concrete that isn’t flat, smooth and free from projections may lead to colour, pattern and gloss inconsistencies. For best results, the substrate should not deviate more than the following distances under a straight edge tool: 3mm over 3m (flatness), 1mm over 150mm (smoothness) or 0.5mm over 50mm (projections). If required, the concrete should be levelled first with a suitable levelling compound. 
• Artepoxy Liquid Marble will not completely hide all cracks, divots or colour in the concrete. To fully conceal, the concrete must be patched first and a solid-colour basecoat applied. 
• Artepoxy Liquid Marble is not designed to produce a perfectly flat, mirror finish on the floor. 
• Application onto highly porous concrete may lead to colour and gloss inconsistencies. If required, the concrete should be primed first with a suitable primer. 
• Artepoxy Liquid Marble should not be used in applications requiring resistance to rapid changes in temperature during service and/or cleaning (i.e. thermal shock). 
• Consistent with all epoxies, Artepoxy Liquid Marble will tend to discolour upon extended UV exposure. Over-coat with Ezypoly (PU topcoat) if required. 
• If splitting a kit, shake/mix Part A and Part B well separately before measuring required volume. 
• If more than one kit is mixed at a time, the product can reach dangerously high temperatures and experience a significantly reduced pot life. 
• Do not add solvents as it can affect performance.
• Do not use below 5°C. 
• Clean up with MEK, acetone or methylated spirits.

Surface Preparation

Concrete:

New concrete surfaces should be allowed to cure for a minimum of 28 days. Old, damaged, cracked and/or heavily contaminated concrete surfaces should be degreased with a detergent and patch repaired prior to surface preparation. Diamond grind or shot blast to obtain a CSP 2-3. Properly prepared surfaces should be structurally sound and free of contamination, laitance and any loose material. Ensure surface is clean, dry and dust-free again if there’s a delay between preparation and application.

Porous Surfaces:

If the concrete is found to be weak, powdery or porous during substrate preparation, apply a suitable primer/sealer first.

Coated Surfaces: 

Maximum delay between coats is 30 hours @ 25°C. Should this time be exceeded the previous coat must be lightly abraded with 80-120 grit paper, vacuumed and wiped with methylated spirits or other suitable solvent. Old, existing films can be over-coated providing they’re in good condition and there are no adhesion issues. If in doubt, a tensile adhesion test should be conducted.

Mixing

WARNING: Part B is a Class 8 Corrosive. For full safety instructions, consult SDS. Wear protective clothing, goggles and gloves to prevent skin and eye contact.

NOTE: Check packaging for correct components before mixing.

Mix product at a ratio of 3:2 by volume. Pour Part B into Part A and blend for 2 minutes.

Artepoxy Liquid Marble kits can be split by using the following weights and volumes to make 1 litre -

Part A	Part B
680g/600mL	410g/400mL

If pigmenting, pre-mix pigment pots into Part A first with a drill mixer before adding Part B.

Application

Brush, roller, squeegee or trowel.
Application thickness - 600 microns (1.67m²/L).

For best results, pour product immediately onto the floor after mixing. Start 50cm from a wall and work towards the exit point pouring in an “S” shaped pattern.

Leave enough mixed product to cut in with a brush next to vertical surfaces and around tight areas. Approximately 100mm is typical.

Perform a rough spread using the squeegee to achieve a relatively even film, allow product to level for 2-3 minutes, then backroll smooth using 12mm x 270mm roller covers.

De-lint all rollers first by wrapping the roller in masking tape and removing. When backrolling, roll in long, even, overlapping strokes to get the product feeling and sounding the same.

To work a fresh batch into the seam of another, pour the material approximately 15cm from the edge and overlap with the roller by about 30cm. Try to minimise the number of seams and keep them as fresh as possible.

Each kit must be applied within the pot life times listed in the Cure Schedule table to ensure best results.

Storage

Keep containers closed when not in use. Store below 40°C. Do not store in direct sunlight. Shelf life is at least 12 months in original, unopened container. Seek advice from your local council regarding accepted disposal methods.

First Aid

CAUTION: KEEP OUT OF REACH OF CHILDREN.  IF ON SKIN: Remove immediately all contaminated clothing. Rinse skin with water. IF IN EYES: Rinse cautiously with water for several minutes. Immediately call a POISON CENTRE (Australia - 13 11 26) or doctor/physician. If skin irritation occurs: Get medical advice/attention. 

WARRANTY DISCLAIMER: The technical data given herein has been compiled for your help and guidance and is based upon our experience and knowledge. However as we have no control over the use to which this information is put, no warranty express or implied is intended or given. We assume no responsibility whatsoever for coverage, performance or damages, including injuries resulting from use of this information or of products recommended herein.